Activity Stream
-
Older Activity
-
2 Weeks AgoHello My name is Nicolas Tyler, and I am located in Los Angeles,CA I work with a CNC router, 3d printing, adn plasma4 replies | 3129 view(s) -
3 Weeks AgoHi, I have Charmilles Robofil 4020 SI & Robofil 4020-1 machine. Please support to install USP port for uploading program it. Currently I'm using a...4 replies | 2713 view(s)
-
3 Weeks AgoHello again, I’ve managed to get the Servo’s to turn the Motors through my AXBB-E Controller just in bench tests at the moment and at a slow speed, I...4 replies | 2356 view(s)
-
3 Weeks AgoI have stripped out all of the wiring and electronics from my Syil as I have now upgrade to UCCNC / AXBB-E and so I have most parts availalble. Let...2 replies | 2351 view(s)
-
2 Weeks AgoHi I have a problem in trying to work out how to machine slots on the inside of a cylinder?? I'm trying to make a billet clutch basket I have a mill...2 replies | 1891 view(s)
-
2 Weeks AgoHi All First post so be gentle :-) I have a MM32L that I have just done a spindle motor conversion on using a 3.6KW servo. I have upped the...2 replies | 1577 view(s)
-
6 Days AgoHi everyone, I'm Nige and I live in the Lincolnshire Wolds in the UK. Here to learn more about CNC machines for woodwork and ultimately decide...1 replies | 989 view(s)
-
4 Days AgoMorning all, I have a ooznest workbee which I have bought the ratrig upgrade kit for. I have started installing the linear rails on the long y axis...2 replies | 369 view(s) -
1 Week AgoHi, selling my warco milling machine.i had this mill running off mach3. The round column has a lock on it that stops it moving round completely when...0 replies | 510 view(s)
-
1 Day AgoHello all i need help I'm quite new to CNC work but i have a problem short story my cnc dug way to far in to my wood went in to spoil board...1 replies | 241 view(s)
-
2 Days AgoIf anyone is interested in this then let me know asap as it will be going next week. Will be leaving ball screws, slides etc one the machine,...0 replies | 250 view(s) -
2 Days AgoHello, Please I have a ABM CNC-F810 Machine but by error I delete some files of the software, please if anyboady have the same machine and send me...0 replies | 229 view(s)
-
2 Days AgoI am putting a 2.2kw spindle into an old spindle moulder to make hopefully an OTT router table, to complement my CNC router in my woodworking. (...0 replies | 184 view(s)
-
19 Hours AgoThanks. What about this stuff? 10hp servo spindle 9 (very heavy ) and the controller 3 centroid servo axis motors ( hj130c8-64s) with centroid...6 replies | 10885 view(s)
-
1 Day Ago£300 for the bt40 spindle and same for toolchanger seems fair6 replies | 10885 view(s)
-
1 Day AgoHi, pricing please?6 replies | 10885 view(s)
-
1 Day AgoYou've bent the ballscrew?1 replies | 241 view(s)
-
1 Day AgoOK, so I had my first band saw blade snap.5 replies | 3574 view(s)
-
4 Days Agoravihotwok replied to a thread What controller would you recomend????? in Control Hardware & Systemshi mate sorry for the delay, I will give it a go :-)2 replies | 2905 view(s)
-
4 Days Agoravihotwok replied to a thread KillerBee Linear rail issue - Am i being fussy? in Machine DiscussionHi m_c, the rails slide fine when they are on their own without anything bolted to them its just when everything is assembled, i think the c beams...2 replies | 369 view(s)
-
4 Days AgoIf the rails are preloaded (which they should be for CNC use), then they should feel a bit tight, but smooth when they move.2 replies | 369 view(s)
-
5 Days AgoAll sorted. Good luck.182 replies | 237828 view(s)
-
5 Days Agohello my freind can you please share with me the link for download emachine 1.935 [email protected] thank you182 replies | 237828 view(s)
-
6 Days AgoHi Gerry. I could do the CS Labs IP-A, plus the MPG module plus the MPG wheel and the two switches (Axis and Speed selection), posted to you for...2 replies | 11730 view(s)
-
6 Days AgoHi Nige Welcome to the Forum1 replies | 989 view(s)
-
1 Week AgoAll should be sorted. Let me know if there are issues.182 replies | 237828 view(s)
-
1 Week AgoHey Buddy, Can you also add me to the dropbox for these files, cheers John182 replies | 237828 view(s)
-
1 Week AgoGerry Hanley replied to a thread Bridgeport Series 1 Interact. Refit/update . Opinions please. in Bridgeport Milling Machinesjust see your post i have an bridgeport interact 1 mark 2 with bosh drives and sem motors and running they bosh drives on single phase and they work...35 replies | 63085 view(s)
-
1 Week Agoyea what price do you want for same thanks Gerry2 replies | 11730 view(s)
-
1 Week AgoAll sorted. Let me know if you need more. Regards.182 replies | 237828 view(s)
cnc build items for sale