Activity Stream
-
Older Activity
-
1 Day AgoI just bought and it's really good 300 on Amazon if you apply the voucher Printing now at 600mm/s with no issues, super nice quality A...0 replies | 101 view(s)
-
2 Days AgoHi, is the SW dongle still available Regards, Theo3 replies | 14230 view(s)
-
2 Days AgoHire somebody with a laser scanner.they will be done in half a day or so and can then provide you with a file,or series of files that will be...2 replies | 216 view(s)
-
2 Days AgoI understand that kitchen fitters use a laser scanner device to digitise the rooms where for example new worktops and units are to be fitted, and...2 replies | 216 view(s)
-
3 Days AgoHey Folks, I'd like to rip out the interior of a boat and refit it utilising the CNC for all the woodwork. Ideally I'd like to CAD it out...2 replies | 216 view(s)
-
6 Days AgoGood advice as expected. Many thanks I'll check the outputs and adjust the speed down to a lower value. It can't hurt to give it a try....29 replies | 22472 view(s)
-
1 Week AgoFor the video above some people have shown an interest in the code so here it is in a zip file. This will open in most text readers if you only want...104 replies | 184204 view(s)
-
1 Week AgoUpdating the software . . . plus more hardware issues found!104 replies | 184204 view(s)
-
1 Week AgoWhat are the terminal numbers on the VFD that the wires are connected to? Green will be X1, which is an input, and I'd guess is used to switch the...3 replies | 4235 view(s)
-
2 Weeks AgoNovamill switches, on my mill anyway, are standard microswitches. Maybe there's a wire dropped off the z switch? If you are seeing the lights...29 replies | 22472 view(s)
-
2 Weeks AgoSo a long awaited update on my Novamill situation. The day after my last post I took a call from Brian at CNC4U, where he made some suggestions to...29 replies | 22472 view(s)
-
2 Weeks AgoHi guys, I've taken the advise of m_c and added an USB controlled breakout board and an extra 24VDC power supply. Tried to hook it up and got the...3 replies | 4235 view(s)
-
2 Weeks AgoAfter sorting out some electrical issues the enclosure is finally working!104 replies | 184204 view(s)
-
2 Weeks Agohttps://www.ebay.co.uk/itm/166758284969 I'm happy to answer any questions. This is complete with safety hood, stepper and spindle drive...0 replies | 1298 view(s)
-
2 Weeks AgoIf you're looking to jump straight into anodizing aluminum without the hassle of trial and error, I found a guide that’s pretty straightforward and...84 replies | 120076 view(s)
-
2 Weeks AgoWelcome.1 replies | 2134 view(s)
-
2 Weeks AgoHi everyone. I'm John from San Bernardino, CA. I have been working in cnc for many years. But I am still new about the operation.1 replies | 2134 view(s)
-
3 Weeks AgoJohn, Briliant. Thanks for letting me know. Good luck in your file transfer. I now use FreeCAD for DXF transfer, although other packages are...173 replies | 185281 view(s)
-
3 Weeks Agoflembo not sure if you got sorted on this but it sounds like your z axis needs reversing. this would be done on the software side rather than at...6 replies | 9953 view(s)
-
3 Weeks AgoHi, it worked perfectly !. This is what i did (win10) : 1) I copied the file : ems.dat.1935.txt...173 replies | 185281 view(s)
-
3 Weeks AgoJohn, Should be OK for you. Let me know if it works, or if it failed.173 replies | 185281 view(s)
-
3 Weeks AgoThe only thing you should consider when using a multimeter is that the aluminium frame is not a good conductor because of the surface oxide which...3 replies | 7263 view(s)
-
3 Weeks AgoNow sold1 replies | 8151 view(s)
-
3 Weeks AgoI agree with A_Camera above. I'm not an electrician but if a live wire came loose and touched the outer case it would become live at mains voltage. ...3 replies | 7263 view(s)
-
3 Weeks AgoYes, of course. You SHOULD connect the aluminium frame to ground. I suppose you mean PE as protective earth, not GND as in DC negative. The same is...3 replies | 7263 view(s)
-
3 Weeks AgoThanks.5 replies | 8406 view(s)
-
3 Weeks AgoAigarsK replied to a thread FOR SALE: Freebie - ViewSonic VX2258WM 21,5" tochscreen in Items For SaleThis item is no longer available.5 replies | 8406 view(s)
-
3 Weeks AgoI'm building something made of aluminium that has mains electronics in it and DC Also Steppers It is a CNC machine technically just a very...3 replies | 7263 view(s)
-
3 Weeks AgoWelcome to MY CNC.1 replies | 7971 view(s)
-
3 Weeks AgoThanks and responded.5 replies | 8406 view(s)
3d Printer Flashforge 5M